-
Servo Manifold Spray HP Bypass Oil Filter C6004L16587
The servo manifold spray hp bypass oil filter C6004L16587 is an oil filter element used in the hydraulic servomotor system. It is located in the high-pressure system of hydraulic servo-motor and used to filter impurities and dirt in the hydraulic servo-motor system. Make the hydraulic servomotor better provide power oil to the main steam valve and governing valve of the steam turbine, so that it can act quickly, reliably and sensitively, and protect the safety of the steam turbine. -
Hydraulic filter element LH0160D020BN3HC
The hydraulic filter element LH0160D020BN3HC is a small feed pump turbine fire resistant oil return filter element, mainly installed on the oil suction path, pressure oil path, return oil pipeline, and bypass filtration system in the system. Hydraulic filter element LH0160D020BN3HC used to remove metal powder and other mechanical impurities from worn components in the oil, keeping the oil circuit clean and extending the service life of the oil.
Brand: YOYIK -
Regeneration device anion filter PA810-002D
The regeneration device anion filter PA810-002D is mainly installed in the regeneration device of the EH oil system, which can filter the EH oil in the device. This filter element, also known as the dry ion exchange resin filter element, has an acid removal ability 7 times higher than that of diatomaceous earth, can improve the resistivity of phosphate ester resistant fuel, avoid electrochemical corrosion of the components, and can filter out metal ions (C, Mg, Fe, etc.) in the EH oil. The regeneration device anion filter PA810-002D adopts a stainless steel structure, which is resistant to compression and not easy to crack, and has low environmental pollution. -
30-150-207 regeneration device diatomite oil filter element
Diatomite filter element 30-150-207 is used for acid removal of regeneration device of fire resistant oil system. When the anti-combustion oleic acid value increases, phosphoric acid reacts with the metal powder in diatomite to produce metal soap or metal salt, which endangers the servo valve. It will often block the filter element, grind the valve core after entering the servo valve, increase the internal leakage at first, and discard the servo valve at last. When the metal salt is found in the system, the servo valve will be damaged in batches. Filtration cannot be improved, and oil change is the important way. -
Regeneration device diatomite filter DL003001
The main function of the regeneration device diatomite filter DL003001 in the regeneration device is to neutralize and filter acidic substances generated by water in the EH oil, ensuring the cleanliness and stability of the EH oil. The main function of the regeneration device diatomite filter DL003001 in the deacidification system of the regeneration device is to adsorb and neutralize acidic substances in the EH oil, preventing corrosion and damage to equipment and systems caused by acidic substances. At the same time, the fire-resistant resin filter element also has good high-temperature resistance and can operate stably for a long time in high-temperature environments. -
RCV actuator filter HQ25.10Z
The RCV actuator filter HQ25.10Z is mainly used in power plant hydraulic servos to filter pollutants and impurities in the oil system, ensuring the normal operation and reliability of the hydraulic servos. It can also be used in the hydraulic and lubrication systems of power plant forced draft fans to filter out solid particles, colloidal substances, and other pollutants in the working medium, effectively controlling the pollution level of the working medium, and ensuring the normal operation of the system.
Brand: YOYIK -
BFP lube filter QF9732W25HPTC-DQ
The installation position of the BFP lube filter QF9732W25HPTC-DQ for the lubricating oil tank of the feed pump turbine is located at the inlet or outlet of the lubricating oil tank, directly installed in the filter element component at the bottom of the oil tank. Its function is to filter impurities and pollutants in the lubricating oil, prevent them from entering the lubrication system, protect various equipment and components in the lubrication system, and maintain the normal operation of the equipment.
Brand: YOYIK -
Generator Stator Cooling Water Filter MSL-125
The generator stator cooling water filter MSL-125 is a filter element installed in the stator cooling water system of a power plant. The filter element adopts a PP wire wound structure, and the polypropylene melt blown filter element is used as the main support skeleton inside, which has a large amount of dirt and circulation. The filter element has a honeycomb structure with sparse exterior and dense interior, which can effectively remove impurities such as suspended solids, rust, and particles in the fluid. The filter element is lightweight and easy to install and disassemble. -
WFF-125-1 Generator stator cooling water filter element
WFF-125-1 Generator stator cooling water filter element is installed in the matching filter MSL-125 of the turbine generator 600MW unit. It is the filter element of the stator cooling water system in the generator hydrogen oil-water system. It’s used to remove more than 5% of the water carried by the treated make-up water or constant cooling water when passing through the filter through the microfiltration filtration device μ M impurities. Micron precision remains unchanged for a long time, because the wound matrix always maintains the same size, which can only be adjusted by changing the quality and physical characteristics of the filter medium inserted. The filter element fully meets the requirements of fiber length processing filter medium, so that the medium fiber can span at least three frames near the outer diameter, and the closer it is to the inner diameter, the more. Combined with the control of filter medium quality and bridging, all filter elements have accurate, consistent and stable precision. -
Generator Stator Cooling Water Filter SGLQ-600A
Regular maintenance of the generator stator cooling water filter SGLQ-600A is essential to ensure that it continues to function effectively. This includes periodic cleaning and replacement of filter elements, as well as monitoring of pressure drop across the filter to identify any signs of clogging. In summary, a generator stator cooling water filter is a critical component in a power generation system that helps to protect the stator from damage and maintain the efficiency of the generator.
-
Hydraulic system air filter element QUQ2-20×1
Hydraulic air filter QUQ2-20x1 is a device used to filter impurities and pollutants in hydraulic system and air system. They are usually composed of a filter element and a shell. The filter element is made of filter paper, filter screen or other materials. It is used to capture and filter particles and pollutants in the fluid, so as to keep the system clean and working normally. The hydraulic air filter is usually installed and used through the interface connected to the system pipe or equipment. -
Compressed Air Filter Element LX-FF14020044XR
The compressed air filter element LX-FF14020044XR has a double sealing ring structure, which adopts a double sealing on the shaft surface to ensure no leakage. Durable and chemical resistant end caps are molded with nylon injection molding and then bonded to the filter core. They are sealed and bonded with high-strength and two component polyurethane for durability and durability.
Brand: YOYIK
/
