The seal of the servo device of the induced draft fan SFG190X159D161 mainly plays the role of preventing leakage and ensuring the stable operation of the servo motor in the fan system. For users, understanding the durability and replacement cycle of the seal, and mastering the installation and maintenance requirements are the key to ensuring the long-term stable operation of the fan.
The main function of the SFG190X159D161 seal is to prevent gas leakage in the servo mechanism and ensure that the servo mechanism can operate stably. The servo mechanism is a key component for controlling the angle of the induced draft fan blades, and the air volume is controlled by adjusting the angle of the blades. The sealing performance of the seal directly affects the working efficiency and stability of the servo mechanism.
The SFG190X159D161 seal is made of special materials and has good high temperature resistance and corrosion resistance. The choice of materials ensures that the seal can work stably for a long time in high temperature and corrosive environments. The structural design of the seal takes into account the dynamic characteristics of the servo mechanism, and can adapt to the displacement and deformation of the servo mechanism during operation to ensure the sealing effect.
The durability of the SFG190X159D161 seal mainly depends on its material and design. The seals are made of high temperature and corrosion resistant materials, such as fluororubber or silicone rubber. These materials can not only withstand high temperature environments, but also resist the erosion of various chemical media, ensuring that the seals can operate stably for a long time under harsh conditions.
The replacement cycle of the SFG190X159D161 seal depends on many factors, including the working environment, frequency of use and maintenance. In general, it is recommended to carry out a comprehensive inspection and necessary maintenance at least once a year. If the seal is found to be worn, cracked or deformed, it should be replaced in time. For fans working in harsh environments, the replacement cycle may need to be shorter.
The installation requirements of the SFG190X159D161 seal are very strict. First, make sure that the installation surface is clean and oil-free, which helps to improve the installation accuracy of the seal. Then, according to the requirements of the drawing, use special tools to accurately install the seal into the servo mechanism to ensure that the seal fits tightly with the servo mechanism to avoid gaps. During the installation process, ensure that the seal is not twisted or damaged, which will affect the sealing effect.
The maintenance requirements of the SFG190X159D161 seal are equally important. Check the condition of the seals regularly to ensure that there is no wear, cracks or deformation. If the seals are found to be damaged, replace them in time to avoid affecting the normal operation of the servo mechanism. In addition, clean the servo mechanism area regularly to remove dust and debris that may affect the sealing effect.
Yoyik offers various types of spare parts for power plant main turbine, generator and auxiliary equipment:
Spindle DTPD60UZ001
HIGH TEMPERATURE STUD 2Cr12NiW1MolV Steam Turbine LP inner cylinder
Oil pump driving gear CO46-09-01B
solenoid valve orifice 33Cr3MoWV Steam Turbine LP MSV
thrust pads FK4E39-K
high-pressure governor valve stem leaking nut R-26 Steam Turbine high and intermediate pressure rotor
Hexagon socket head cap screw GB00070.1C1030 1Cr15Ni36W3Ti Steam Turbine Reheated steam vavle
Reducing Tee Joint 16Mn Steam Turbine Intermediate pressure steam inlet chamber
Special double head bolts M42*3*240 40Cr2MoVA Steam Turbine nozzle chamber
Stacked sealing ring DTPD60UZ016
Bearing seat end cover FAID67-02-06
Inside Oil Seal Spring DG600-240-05-11
HP casing HP inlet pipe bolt R-26 Steam Turbine Outer casing
HP casing nut ZG230-450 Steam Turbine LP casing
Spring W9
End shield processing (excitation) Generator QFSN-300-2
Nut GB0006170C0020 2Cr11MolVNbN Steam Turbine Steam chamber
turning device assembly 34CrNi3Mo Steam Turbine High pressure combined valve
Insulation bolt Generator QFQ-50-2
Motor side coupling DTYJ60FM002
Post time: Jul-31-2024