-
LVDT Position Sensor ZDET-200B
LVDT Position Sensor ZDET-200B is based on the principle of differential inductance, which converts linear moving mechanical quantity into electric quantity, so as to automatically monitor and control displacement. It has the advantages of high temperature resistance, small size, high accuracy, stable performance, reliable operation and long service life. It can run continuously for one overhaul cycle of steam turbine without maintenance and replacement.
Brand: YOYIK -
CS-V hydraulic system filter Differential pressure transmitter
The function of the differential pressure transmitter CS-V is to instruct the staff to clean or replace the filter element in time after the filter element of the oil filter is blocked. -
Differential Pressure Switch CMS
The Differential Pressure Switch CMS integrates electrical communication with target communication, enabling both electrical and target communication. If a malfunction occurs in an electrical component or circuit, causing the electrical signal to fail to alarm, the visual signal at the other end can still accurately alarm, thus improving the reliability of the transmitter.
Brand: YOYIK -
Differential pressure transmitter CS-III
The pressure difference transmitter CS-III is used to alarm the blockage of the oil filter in the form of a switch, or to cut off the control circuit related to the hydraulic system in the form of a switch, in order to ensure the safe and normal operation of the main engine and hydraulic system.
Brand: YOYIK -
Coal Feeder Load Cell AC19387-1
The load cell AC19387-1 is an important accessory on the coal feeder. The load cell AC19387-1 used on the coal feeder is gravity sensor, belongs to the scope of force-sensitive sensor; it normally uses the metal resistance strain gauge as a force change detection device. -
Hydraulic Adjustable Pressure switch ST307-350-B
A range of piston-operated pressure switches for general applications where an electrical signal is needed to indicate a given pressure condition in a hydraulic circuit. The microswitch is actuated by the operating plate of an adjustable loading spring. The spring load holds the operating plate against the switch until applied hydraulic pressure on a small piston forces the operating plate away from the switch to change over the switch contacts. The switch will reset when the hydraulic pressure falls by a small differential. -
Pressure Switch ST307-V2-350-B
Pressure switch ST307-V2-350B is usually used as an action indicator signal in protection and automatic control devices for AC and DC operations. The relay adopts imported ultra-small components, with reasonable layout and structure of electronic circuit design. The pressure switch is driven by an adjustable loading spring operating board. The spring load holds the operating plate on the switch until hydraulic pressure is applied to the small piston to force the operating plate far away from the close to switch contacts. When the hydraulic pressure drops by a small difference, the switch will reset. -
DWQZ series proximitor Axial displacement Eddy current sensor
Eddy current sensor is a non-contact linear measurement tool. It has the advantages of good long-term reliability, wide measurement range, high sensitivity, high resolution, fast response, strong anti-interference, free from the influence of oil and other media, so it is widely used in power, petroleum, chemical, metallurgical and other industries, such as steam turbine, water turbine, blower, compressor, gearbox, etc Dynamic and static non-contact displacement measurement of large rotating machinery such as large cooling pump.
DWQZ series Eddy current sensor is composed of three parts: DWQZ probe, DWQZ extension cable and DWQZ proximitor. -
SZ-6 Series Integrated Vibration Sensor
SZ-6 magnetoelectric speed sensor is an inertial sensor. It uses the principle of magnetoelectric induction to transform the vibration signal into a voltage signal, which is directly proportional to the vibration speed value. The sensor can be used to measure mechanical vibration with rotational speed as low as 5Hz. -
Vibration speed Sensor HD-ST-A3-B3
HD-ST-A3-B3 Vibration speed sensor is connected with intelligent vibration monitor or transmitter to measure various displacements and velocities, detect early failures of various rotating machinery, and output standard 4-20mA current signals to PLC, DCS, and DEH systems. It provides signals for monitoring instruments to predict and alarm mechanical faults.
Brand: YOYIK -
Magnetoresistive speed sensor SZCB-01-A1-B1-C3
The Magnetoresistive speed sensor SZCB-01-A1-B1-C3 adopts the principle of electromagnetic induction to achieve speed measurement. This sensor has strong output signal, good anti-interference performance, convenient installation and use, and can be used in harsh environments such as smoke, oil and gas, and water vapor.
Brand: YOYIK -
Integrated Bearing Vibration Transmitter JM-B-35
The Integrated Bearing Vibration Transmitter JM-B-35 is integrated vibration velocity transducer, which uses two-wire form, provide 4-20mA current signal, and rotating machinery vibration or bearing bush proportional to the velocity. It automatically collect machine vibration signals and converts the analog signal for PLC, DCS and DEH system. Mainly applies to measure the absolute vibration ( such as bearing vibration) of the rotary machinery. The Vibration Transmitter JM-B-35 all stainless steel shell integration designs, and output has polarity protection.
Brand: YOYIK
/
