-
Slide Gate Valve Spare Parts Kit 200×200 PN1.0: Scratch or Just a Trapped Particle?
Coal conveyor lines leak a little after the gate shuts. Fine material gets past the seal, downstream side, right after closure. Most of the time it’s nothing — a bit of ash or pulverized coal sitting between the plate and the seat, gone by the next cycle. Sometimes it’s a groove worn ...Read more -
A2201 Seal Kit: Reading a Sluggish Dome Valve Before You Open It
A dome valve that used to snap open and closed now takes its time. Maybe it pauses partway through the stroke. Someone checks the air pressure gauge. Normal. So what now? The A2201 seal kit rebuilds the actuator cylinder on a DN100 pneumatic conveying dome valve. Worn internal seals are one usual...Read more -
D633-460B Servo Valve: Jitter, Drift, and the Risk of Fixing It Wrong
A servo valve like the D633-460B sits at the center of DEH position control. It moves the main steam valve and the governing valve to exact positions, based on an electrical command. Feedback tells the system where the valve actually sits. When that feedback starts jittering, or the zero point dr...Read more -
P17458C-01 Embedded Sealing Ring: Chasing Dust Leaks That Come and Go
A dome valve seals by inflating a ring, not by clamping metal on metal. The P17458C-01 is that ring — silicone rubber, built into the dome valve, expanding under air pressure to press against the dome and shut off dust flow. Simple concept. But when dust starts leaking after the valve closes, and...Read more -
SFQ41F-16C Double Ball Valve: The Standby Side Problem
Two outlets, one valve body. That is the basic idea behind the SFQ41F-16C ball valve. One line stays in service. The other sits ready, waiting for a switch, a maintenance need, or a flow split. Simple on paper. In an oil station running for years without stopping, the standby side raises a questi...Read more -
DBDS10G10/5 Direct-Acting Relief Valve: Reading a Low-Pressure Fault
A relief valve has one job. Open when pressure is too high. Stay shut the rest of the time. The DBDS10G10/5 is a direct-acting relief valve with a poppet-style spool. It can act as a safety valve, protecting the system from over-pressure. It can also act as a back-pressure valve, holding pressure...Read more -
DG4V-3-2A-VM-U-SA7-60 Solenoid Directional Control Valve: What Happens When It Doesn’t Fully Reset
There is a kind of failure in EH oil and jacking oil systems that does not show up as an alarm right away. The valve does not fail closed. It does not fail open. It just does not quite get all the way back to where it should be. A solenoid directional control valve like the DG4V-3-2A-VM-U-SA7-60 ...Read more -
YOX II500 Hydraulic Coupling with Brake: Does the Brake Really Wear Out the Output Bearing?
Coal handling equipment doesn’t get treated gently. Conveyor belts start up under load, coal mills need protecting from jams and blockages, and somewhere between the motor and the driven equipment you need something that can soak up a soft start and step in when things go wrong. A hydraulic...Read more -
WJ40F1.6P-II Bellows-Sealed Globe Valve: Surviving Vibration in Hydrogen-Cooled Generator Systems
Hydrogen-cooled generators are not quiet machines to build valves around. Between the rotating shaft line, the hydrogen coolers, and the piping that ties the whole cooling loop together, a valve sitting anywhere near this equipment lives with constant low-level shaking for years at a time. The WJ...Read more -
Cone Valve Sealing and Particle Contamination in Steam Turbine EH Oil Systems: A Look at the SV13-16-C-0-00
When you’re picking a solenoid valve for an EH oil system, the decision is almost never just about the valve on its own. It’s about how that valve’s internal geometry holds up inside oil that’s never truly clean, under thousands of open-close cycles over its life, and unde...Read more -
SWF1 Stator Cooling Water Filter: Copper’s Climbing but the Pressure Gauge Says Nothing’s Wrong
In a generator stator cooling water system, water quality is directly related to the long-term reliability of the stator winding. Copper tubes and hollow conductors are continuously exposed to circulating demineralized water. Any corrosion products, suspended particles, or other contaminants ente...Read more -
DP602EA01V/-W Main Pump Filter: Real Clog or Just Cold Oil?
Cold morning start, EH oil hasn’t warmed up yet, and the differential pressure reading across the DP602EA01V/-W suction filter is higher than anyone likes. Is the filter actually dirty, or is this just what cold, thick oil does to a pressure reading during a normal startup? Getting this wro...Read more
/
News
- English
- French
- German
- Portuguese
- Spanish
- Russian
- Japanese
- Korean
- Arabic
- Irish
- Greek
- Turkish
- Italian
- Danish
- Romanian
- Indonesian
- Czech
- Afrikaans
- Swedish
- Polish
- Basque
- Catalan
- Esperanto
- Hindi
- Lao
- Albanian
- Amharic
- Armenian
- Azerbaijani
- Belarusian
- Bengali
- Bosnian
- Bulgarian
- Cebuano
- Chichewa
- Corsican
- Croatian
- Dutch
- Estonian
- Filipino
- Finnish
- Frisian
- Galician
- Georgian
- Gujarati
- Haitian
- Hausa
- Hawaiian
- Hebrew
- Hmong
- Hungarian
- Icelandic
- Igbo
- Javanese
- Kannada
- Kazakh
- Khmer
- Kurdish
- Kyrgyz
- Latin
- Latvian
- Lithuanian
- Luxembou..
- Macedonian
- Malagasy
- Malay
- Malayalam
- Maltese
- Maori
- Marathi
- Mongolian
- Burmese
- Nepali
- Norwegian
- Pashto
- Persian
- Punjabi
- Serbian
- Sesotho
- Sinhala
- Slovak
- Slovenian
- Somali
- Samoan
- Scots Gaelic
- Shona
- Sindhi
- Sundanese
- Swahili
- Tajik
- Tamil
- Telugu
- Thai
- Ukrainian
- Urdu
- Uzbek
- Vietnamese
- Welsh
- Xhosa
- Yiddish
- Yoruba
- Zulu
- Kinyarwanda
- Tatar
- Oriya
- Turkmen
- Uyghur